Start by measuring the wall width and height. For me it’s 45.5 inches wide by 107 inches or so tall. My baseboard is 6 inches tall, leaving me with 101 inches of height. I decided on 5 inch high stripes. With a 45.5 inch width, I decided on roughly three 15 inch columns. We'll start with how I did the design since painting the base color is basic…just paint the wall! For the stripes, using a yard stick, I made pencil marks every 5 inches above the baseboard to the ceiling on the wall.
I then connected the dots using a light pencil line and my level to create evenly spaced horizontal lines up the wall from baseboard to ceiling. Because dividing 45.5 into 3 equal sections gets an odd long number, I made a mark in the center of each horizontal line on the wall (for me that was 27.75). From the center, I made a pencil mark at 7.5 inches left and right. My center column on the wall will measure exactly 15 inches. The left and right columns will be slightly larger than the center 15 inch column (but unnoticeable).
I then used my level to connect the dots to mark my vertical lines and to create three columns on the wall.
Time for FrogTape®! Starting with the center column, I taped off the “outside” of every other rectangle.
Burnish the edges of the FrogTape with a thumbnail.
Using a dense foam roller, I painted each rectangle. I did three coats since I painted black on white.
While the last coat of paint was still wet, I removed the FrogTape by pulling away from the paint. Let dry 24 hours.
Time to paint the left and right columns! Using FrogTape® Delicate Surface (since the black paint is still fairly fresh), I taped off each rectangle (staggered from the center column). Again, burnish the edges of the FrogTape with a thumbnail then paint. I did three coats throughout the day.
While the last coat of paint is still wet, remove the FrogTape by pulling away from the paint. Let dry 24 hours.
As is the way with DIY, I was not liking my initial design. It was more of a check board/racing flag look. Not what I was going for at all!
The fix: So, on the right and left columns I applied a strip of FrogTape Delicate Surface to the white rectangle boxes/stripes…one on the top edge, one on the bottom edge.
Then painted the white middle section of each rectangle black. Again, 3 coats!
While the last coat was still wet, I removed the FrogTape….and the result was MUCH BETTER! It has a sort of 3D look to it. I was going to do that last paint step on the middle column’s black rectangle with white paint in the center but ended up liking it as is.
Start by measuring the wall width and height. For me it’s 45.5 inches wide by 107 inches or so tall. My baseboard is 6 inches tall, leaving me with 101 inches of height. I decided on 5 inch high stripes. With a 45.5 inch width, I decided on roughly three 15 inch columns. We'll start with how I did the design since painting the base color is basic…just paint the wall! For the stripes, using a yard stick, I made pencil marks every 5 inches above the baseboard to the ceiling on the wall.
I then connected the dots using a light pencil line and my level to create evenly spaced horizontal lines up the wall from baseboard to ceiling. Because dividing 45.5 into 3 equal sections gets an odd long number, I made a mark in the center of each horizontal line on the wall (for me that was 27.75). From the center, I made a pencil mark at 7.5 inches left and right. My center column on the wall will measure exactly 15 inches. The left and right columns will be slightly larger than the center 15 inch column (but unnoticeable).
I then used my level to connect the dots to mark my vertical lines and to create three columns on the wall.
Time for FrogTape®! Starting with the center column, I taped off the “outside” of every other rectangle.
Burnish the edges of the FrogTape with a thumbnail.
Using a dense foam roller, I painted each rectangle. I did three coats since I painted black on white.
While the last coat of paint was still wet, I removed the FrogTape by pulling away from the paint. Let dry 24 hours.
Time to paint the left and right columns! Using FrogTape® Delicate Surface (since the black paint is still fairly fresh), I taped off each rectangle (staggered from the center column). Again, burnish the edges of the FrogTape with a thumbnail then paint. I did three coats throughout the day.
While the last coat of paint is still wet, remove the FrogTape by pulling away from the paint. Let dry 24 hours.
As is the way with DIY, I was not liking my initial design. It was more of a check board/racing flag look. Not what I was going for at all!
The fix: So, on the right and left columns I applied a strip of FrogTape Delicate Surface to the white rectangle boxes/stripes…one on the top edge, one on the bottom edge.
Then painted the white middle section of each rectangle black. Again, 3 coats!
While the last coat was still wet, I removed the FrogTape….and the result was MUCH BETTER! It has a sort of 3D look to it. I was going to do that last paint step on the middle column’s black rectangle with white paint in the center but ended up liking it as is.
related projects
How to Paint Sharp Lines on Textured and Uneven Surfaces
Painting sharp lines on textured or uneven surfaces can be frustrating. Here are some tips to get the job done right.
Melissa Woods took inspiration from the 2023 Design Trend "Bohemian Bazaar" to create this colorful mural. Using bright, bohemian colors, FrogTape® and a few paint rollers, Melissa, from Welcome to the Woods, made an amazing feature for a bedroom.